Manufacturing plants and industrial sites
Facilities Engineer / Facilities Manager (plant buildings and utilities)
Also posted as Plant Engineer, Lead Facilities Engineer, Facilities Mechanical Engineer, Utilities Engineer, Site Services Manager, Facilities Operations Manager, Senior Manager Facilities and Workplace Experience, Building & Grounds Manager, Plant Engineering Manager
Owns the buildings and the plant utilities that feed production: compressed air (often multiple pressure levels), boilers and steam, chillers and cooling towers, process and potable water, HVAC and the BMS, electrical distribution, fire systems and grounds. Writes PMs for utility assets, manages contractors, sets long-range equipment plans and budgets.
What they do
- Responsible for all operational support equipment including compressed air systems (8 Bar and 200 Bar), chillers, boilers, industrial vacuum blowers, electrical, pneumatic and mechanical components (Continental)
- Responsible for the overall reliability of all plant utilities: boiler and steam, high and low pressure compressed air, water utilities, process chillers, cooling towers, HVAC and the building management system (fairlife, via search)
- Create and modify plant maintenance procedures and PM's to provide optimum maintenance coverage and extended equipment life (fairlife, via search)
- Manages contractors doing maintenance and project work on facilities equipment, building and campus grounds maintenance (Continental)
- Oversee construction and renovation projects; plan, administer, and control budgets for contracts, equipment, and supplies (O*NET)
- Prepare and review operational reports and schedules to ensure accuracy and efficiency (O*NET)
What they measure
- utility-caused production downtime
- compressed air kW/100 cfm and leak rate
- boiler efficiency and steam cost
- chiller kW/ton
- PM compliance on utility assets
- contractor spend vs budget
- water use per unit
- Leak rate % of total system flow
Systems they use
- BMS/BAS
- CMMS (SAP, Maximo, eMaint, Fiix)
- compressor and boiler controls
- SCADA (listed by O*NET)
- energy monitoring software
- AutoCAD/Revit
- contractor and permit-to-work systems
Certifications
- BSc engineering + ~5 yrs (Continental)
- CFM (IFMA) / FMP
- CEM
- boiler/stationary engineer licence where required
- PE (preferred in fab postings)
Standards they work to
- NFPA 70B (electrical equipment maintenance): A forum poster says the 2023 edition is largely new with 'should' replaced by 'shall'; a moderator says NFPA 70B can be used by any service organization, and another poster notes it is not adopted by any jurisdiction.
Jobs to be done
- Keep utilities ahead of production demand · Capital planningWhen production adds a shift or a line, I want compressed air, steam, chilled water and power capacity versus demand trended, so I can forecast when a utility becomes the constraint and plan capital before it does. BoardReport
- Catch utility failures before the line does · UptimeWhen a compressor, boiler or chiller degrades, I want alarms on pressure, dew point, temperature and flow with the lines that depend on each utility, so I can respond before a dry-air or steam loss stops production. AlertsMapBoard
- Hunt compressed air leaks and overpressure · EnergyWhen compressed air cost climbs, I want leak-survey findings, header pressure and compressor kW per cfm tracked over time, so I can cut what one source calls the purest form of waste and justify the fixes. BoardMapWorkflow
- Manage contractors and service contracts · VendorWhen contractors maintain HVAC, boilers or cleanrooms, I want their PM completion, response times and permits tracked against the contract, so I can hold the provider to SLAs and keep compliance evidence. ScorecardReportWorkflow
- Keep building systems and fire protection compliant · ComplianceWhen fire alarm, sprinkler, emergency lighting or elevator inspections come due, I want them scheduled with evidence and deficiencies tracked, so I can show the authority having jurisdiction and insurers a clean record. ScheduleChecklistReport
Pain points
- Facilities engineers in manufacturing are posted under industrial, manufacturing or facilities engineer titles interchangeably (O*NET 17-2112 lists Facilities Engineer and Plant Engineer as reported titles) (heard in O*NET 17-2112.00 Industrial Engineers)
- Battery energy storage on site brings design and risk mitigation questions to plant engineering (heard in Plant Engineering front page (index))
- A practitioner on PLCtalk calls compressed air the most expensive utility in a manufacturing plant, potentially far costlier than any other utility, which is why leaks and misuse matter. (heard in Air Compressor Starting Current (PLCtalk))
- DOE says compressed air leaks waste as much as 20-30% of compressor output and also cause fluctuating system pressure that makes air tools and air-operated equipment run less efficiently, possibly affecting production, plus extra compressor cycling and maintenance. (heard in Minimize Compressed Air Leaks (US DOE Compressed Air Tip Sheet #3, revised 2004-08))
- A Mike Holt's Forum poster says most of NFPA 70B 2023 is new and 'should' has been replaced with 'shall'; a respondent argues it is only a standard not adopted by any jurisdiction and no more powerful than ANSI/NETA standards. (heard in Discussion about NFPA 70 B (Mike Holt's Forum))
Sources
- O*NET 11-3013.00 Facilities Managers
- Continental: Lead Facilities Engineer
- LHH: Facility Engineer, Wilton CT
- fairlife careers board (Greenhouse)
- Plant Engineering: How compressed air systems work (Atlas Copco author)
- TSMC Arizona: Facilities Water Engineer (posted Oct 8, 2026)
- Pfizer (via The Muse): Lead Engineer, Facility Maintenance Operations
- Pfizer Singapore (via career.io): Senior HVAC/BMS Engineer
- O*NET 17-2112.00 Industrial Engineers
- O*NET 51-8021.00 Stationary Engineers and Boiler Operators
- Food Processing (sponsored, SMC): Combustible Dust: A Hidden Hazard That Demands Reliable Dust Collection
- Plant Engineering front page (index)
- Minimize Compressed Air Leaks (US DOE Compressed Air Tip Sheet #3, revised 2004-08)
- Kraft Heinz: Powerhouse Operator, Columbia MO
- Plant Engineering: How to write and evaluate a plant's emergency drills
- Discussion about NFPA 70 B (Mike Holt's Forum)
- Air Compressor Starting Current (PLCtalk)
More roles in manufacturing plants and industrial sites
- Director of Manufacturing Operations / VP Operations
- Plant Manager
- Operations / Production Manager
- Production Supervisor
- Maintenance Manager
- Maintenance Supervisor
- Maintenance Planner / Scheduler
- Reliability Engineer
- Maintenance Technician (Mechanical / Multi-craft)
- Electrical / Instrumentation & Controls Technician
- Utilities / Powerhouse Operator
- Controls / Automation Engineer
- OT/IT Manufacturing Systems Engineer (MES, historian, plant network)
- Process Engineer
- Industrial Engineer
- Continuous Improvement / Lean / OpEx Manager
- Quality Manager
- EHS Manager / Safety Coordinator
- Industrial Hygienist
- Energy Manager (plant / ISO 50001)
- Environmental Compliance Manager / Engineer
- Plant Security Manager (and Security Officers)
- Tooling / Tool Room Lead (Tool & Die)
- Plant Materials / Warehouse Coordinator (plant-side)
- Sanitation Manager (food & beverage)
- Cleanroom / Fab Facilities Engineer (semiconductor)
- GMP Facilities / Utilities & Validation Engineer (pharma)
- Condition Monitoring / Predictive Maintenance (PdM) Technician
- Industrial Wastewater / Pretreatment Operator
Every kind of facility
- Airports
- Cross-cutting and portfolio roles
- Data center
- Education campuses
- Government, civic and public-safety buildings
- Hospitals and healthcare facilities
- Laboratories and life-science facilities
- Manufacturing plants and industrial sites
- Multifamily residential and rental housing
- Office buildings and corporate workplaces
- Retail, hospitality and venues
- Transit, terminals and parking
- Utilities and critical process infrastructure
- Warehouses and distribution centers